Intitially I ordered the straight 1 & 1/4 to 2" adapter for my 2002 Montana van for the carrier I purchase here. Unfortunately as the area I live in has a lot of dips etc in the roads. and sometimes the carrier while loaded with my wife's mobility scooter would hit the pavement cover over one of these dips in the roadway. I ordered this adapter and it arrived within 3 days. I needed to cut the plastic cover on the rear bumber so the tongue would go far enough into the hitch that was installed on my van. That was the only difficulty I encountered and wasn't that hard to deal with. No the carrier doesn't bottom out with her scooter mounted.
I have a Subaru Forester, and the only receiver hitch I could make fit was a 1.25" receiver. When using a hitch mounted platform, I needed to use an adapter that went straight out of the 1.25" receiver, and then, with a little luggage in the rear of the SUV, the platform was getting too close to the ground for my comfort. This raises it up nicely (and saved me from having to weld something on my own).
Excellent product. Well made. Very sturdy. Paint job is excellent to say the least. Give enough clearance to the rear bumper of the vehicle. It can be position to raise the bike rack or to lower it. It fits perfectly on the 1-1/4" section on the vehicle. I strongly recommend it if you are trying to get a 1-1/4" to 2" hitch. Delivery was quick.
I am very pleased with it. Extra heavy welds it will allow me to use my Class II trailer ball and use my Class II alum. carrier basket to Florida from Michigan! Extra room inside the little Vibe.
needed to raise my box lift on my car as was too low now it works great
We purchased this adapter, to raise a chair carrier attached to our car. This is going to work just fine! So excited to be able to use our carrier now! Thank you for making such a solid product!
Product was as described, fast ship. Will work perfectly to raise cargo carrier on my motorcycle to avoid bottoming out.
I like this hitch .It comes as pictured .Very well made shipping was quick.
I have been needing and adapter for a power chair carrier that would raise the carrier 3 or 4 inches and was strong enough to carry 200 pounds. This rising adapter fit the bill perfectly.
Installed hitch on 2012 Chevy Cruz but bike rack was to low to ground, searched for riser that would work but be far enough from bumper, this one works and has at least 3/4 inch or more clearance!
I was very pleased with this product!! It fit perfectly just as it should!! I was very pleased with the extremely fast shipping and quality of this actproduct !! I would definitely recommend this product!!
The DRH-2 is the only rise adapter I've found that will fit and clear the 2007 to 2011 Camry bumper when used with my Draw-Tite 36426 hitch (sister hitches: Hidden Hitch 90152 and Reese 51190) as it's somewhat recessed in. All other rise adapters were too short and would not let the 2" receiver portion clear the bumper. This hitch allows for approximately 1 7/8" of bumper clearance when measured from the rearmost, topmost portion of the 2" receiver of the adapter on my Camry. Very sturdy build.
I needed the riser since I was using it for a bike rack on my 2015 Corolla and needed the ground clearance. I also needed the extra spacing of the pin hole to maintain clearance from the back bumper. This product is everything it is advertised to be, delivery was speedy especially this time of year, and I will always look to Discount Ramps for future needs.
Great product, seems to work good
Fantastic 1-1/4 to 2 inch converter. holds my bike transporter just that extra bit higher to keep the bicycle wheel away from the road surface. Love this thing....
This is a very nice hitch converter for a Polaris Rxr 800. Also the fact that you can turn it over and change the height of the hitch is great.
Glad this 1 1/4" to 2" hitch adapter was available with two holes so you can adjust the depth it goes into receiver hitch. Lucky for me it went in deeper, so I feel it is a bit more stable. Most other competitors only had one hole. Now I'm able to us my bike carrier without scraping the ground. Thanks a bunch!
Just received this DRH-2 hitch adapter today 09/12/2014. I have a cargo carrier for my 09 Madza 5 van. I had a standard 1 1/4" to 2" adapter. It was dragging in low spaces. This unit raised it enough to not allow the carrier to drag.